Tekin - Industria e Comércio de Equipamentos de Segurança

Fone: (11) 4396 5777 tekin@tekin.com.br Estrada Galvão Bueno, 4146 - Bairro Batistini - São Bernardo do Campo -São Paulo - Brasil

TEKIN
Industria e Comércio de Equipamentos de Segurança
Armazenamento
Armários para armazenamento e estocagem, especialmente desenvolvidos para centralizar inflamáveis com segurança.
Transferencia
A Tekin possui uma enorme quantidade de produtos de transferência, cada um elaborado para uma finalidade .
Uso
Práticos para linhas de produção, que envolvem líquidos inflamáveis, aliando a qualidade de serviços a segurança e a economia obtendo assim melhores resultados com o operador.
Descarte
Ideais para simplificar suas tarefas de coleta e contenção, com segurança.
Outros...
Barras Anti-Pânico, Pallet de Contenção para IBC's , abafadores de faísca, cabos de aterramento, etc...

voltar

Key Excerpts
Environmental Products
Drum Equipment

DOT 49 CFR 173.3 (c) Salvage Drums:
Packages of hazardous materials that are damaged, defective or found leaking and hazardous materials that have spilled or leaked (including used sorbents) may be placed into a metal or plastic removable head drum that is compatible with the lading and shipped for repackaging or disposal under the following conditions:
1. Except as provided in paragraph (c)(7) of this section, the drum must be a UN 1A2, 1B2, 1N2 or 1H2 tested and marked for Packing Group III or higher performance standards for liquids or solids and a leakproofness test of 3 psi.

EPA 40 CFR 261.23(a)(6):
In a report prepared for EPA by the Office of Solid Waste and Emergency Response, it was noted that aerosol cans would be a RCRA hazardous waste because they demonstrate the hazardous characteristic of reactivity. When an aerosol can is depressurized (vented) to atmospheric pressure using Justrite’s Aerosolv, the danger from reactivity (40 CFR 261.23(a)(6)) is thereby removed. Hence, one has taken a hazardous waste to a non-hazardous state.

OSHA 29 CFR 1910.106(d)(4)(v):
Storage in inside storage rooms. In every inside storage room there shall be maintained one clear aisle at least 3 feet wide. Containers over 30 gallons capacity shall not be stacked one upon the other. Dispensing shall be by approved pump or self-closing faucet only.

OSHA 29 CFR 1910.106(e)(2)(iv)(d):
Flammable or combustible liquids shall be drawn from or transferred into vessels, containers, or portable tanks within a building only through a closed piping system, from safety cans, by means of a device drawing through the top, or from a container or portable tanks by gravity through an approved self-closing valve. Transferring by means of air pressure on the container or portable tanks shall be prohibited.

OSHA 29 CFR 1910.106(d)(2)(ii):
Emergency venting. Each portable tank shall be provided with one or more devices installed in the top with sufficient emergency venting capacity to limit internal pressure under fire exposure conditions to 10 psig, or 30 percent of the bursting pressure of the tank, whichever is greater. The total venting capacity shall be not less than that specified in paragraphs (b)(2)(v)(c) or (e) of this section. At least one pressure-activated vent having a minimum capacity of 6,000 cubic feet of free air (14.7 psia and 60ºF) shall be used. It shall be set to open at not less than 5 psig. If fusible vents are used, they shall be actuated by elements that operate at a temperature not exceeding 300ºF.

The Clean Air Act Amendments of 1990 have mandated Hazardous Organic National Emission Standards for Hazardous Air Pollutants, known as the HON Rule. EPA encourages control of these “fugitive emissions.”

EPA 40 CFR 264.173: Management of containers.
(a) A container holding hazardous waste must always be closed during storage, except when it is necessary to add or remove waste.
(b) A container holding hazardous waste must not be opened, handled, or stored in a manner which may rupture the container or cause it to leak.

OSHA 29 CFR 1910.106(e)(6)(ii):
Grounding. Class I liquids shall not be dispensed into containers unless the nozzle and container are electrically interconnected. Where the metallic floorplate on which the container stands while filling is electrically connected to the fill stem or where the fill stem is bonded to the container during filling operations by means of a bond wire, the provisions of this section shall be deemed to have been complied with.